Product Description
Liquid turbine flowmeter is a kind of precision flow measuring instrument, which can be used to measure the flow and total amount of liquid with the corresponding flow integrating instrument. Liquid turbine flowmeters are widely used in measurement and control systems in petroleum, chemical industry, metallurgy, scientific research and other fields. Liquid turbine flowmeters with sanitary fittings can be used in the pharmaceutical industry.
Turbine flowmeter working principle: Fluid flows through the sensor shell, because the blade of the impeller has a certain angle with the flow direction, the impulse force of the fluid makes the blade have a rotational torque, and after overcoming the friction torque and fluid resistance, the blade rotates, and the rotational speed is stable after the torque is balanced. Under certain conditions, the rotational speed is proportional to the velocity. It is in the magnetic field of the signal detector (composed of magnetic steel and coil), the rotating blade cuts the magnetic field line, and periodically changes the magnetic flux of the coil, so that both ends of the coil are induced by the electrical pulse signal, the signal is amplified by the amplifier, forming a continuous rectangular pulse wave with a certain amplitude, which can be transmitted to the remote display instrument, showing the instantaneous flow and cumulative amount of fluid.
Turbine flowmeter is a kind of speed instrument, which has the advantages of high precision, good repeatability, simple structure, high pressure resistance, wide measuring range, small size, light weight, small pressure loss, long life, simple operation, easy maintenance, etc., used to measure the volume flow and accumulation of low viscosity, no strong corrosion and clean liquid in closed pipelines. It can be widely used in petroleum, chemical industry, metallurgy, organic liquid, inorganic liquid, liquefied gas, urban gas pipe network, pharmaceutical, food, paper and other industries.
Product Parameters
| Executive standard |
Turbine flow sensor(JB/T9246-1999) |
| Connection mode |
Thread, clamp, flange, clamp type |
| Accuracy |
±1%R,±0.5%R,±0.2%R (to be customized) |
| Sensor material |
304, 316 stainless steel, etc |
| Use conditions |
Medium temperature:-20ºC~+120ºC Ambient temperature:-20ºC~+60ºC |
| Relative humidity:5%-90% Atmospheric pressure:86Kpa~106Kpa |
| Signal output function |
Pulse signal, 4-20mA signal |
| Communication output function |
RS485 communication, HART protocol, etc |
| Working power supply |
External power supply: 24VDC±15%, ripple ≤±5%, suitable for 4-20mA output, pulse output, RS485, etc |
| Internal power supply: 1 set of 3.6V10AH lithium battery, the battery voltage can work normally at 2.0-3.0V |
| Signal line interface |
Basic model: Hausmann connector or three-core cable; Explosion-proof type, internal thread M20*1.5 |
| Explosion-proof class |
Exia II CT or Exd II BT6 |
| Protection class |
IP65 or higher customizable |
Detailed Photos
Installation Instructions
- Requirements for the straight pipe section: The flowmeter must be installed horizontally on the pipeline (the inclination of the pipeline is within 5), and the flowmeter axis should be concentric with the pipeline axis when installed, and the flow direction should be consistent. The length of the upstream pipe of the flow meter should be not less than 2D equal straight pipe section, if the installation site is sufficient, it is recommended that the upstream straight pipe section is 20D and the downstream is 5D.
- Requirements for bypass pipes: In order to ensure that the normal use of the medium is not affected when the flow meter is repaired, a cut-off valve (stop valve) should be installed on the front and back pipes of the flow meter, and a bypass pipe should be set up. The flow control valve should be installed in the downstream of the flow meter, and the stop valve installed in the upstream when the flow meter is used must be fully opened to avoid the unsteady flow of the upstream part of the fluid.
- Requirements for the external environment: When the flow meter is installed indoors, it must be installed outdoors, and it must use sun protection and rain protection. Lightning protection measures to avoid affecting the service life.
- Requirements for impurities in the medium: In order to ensure the service life of the flow meter, a filter should be installed in front of the straight pipe section of the flow meter.
- Installation location: The flowmeter should be installed in a place that is easy to maintain and free from strong electromagnetic interference and thermal radiation
- Requirements for installation and welding: The user has another pair of standard flanges welded on the front and back pipes. Welding with flow meter not allowed! Before installing the flow meter, the welding slag and other dirt in the pipe should be strictly removed, and the pipe of equal diameter (or by-pass pipe) should be used to replace the flow meter for purging the pipe. To ensure that the flow meter is not damaged during use. Installation flow time, flange between the sealing gasket can not be concave into the pipeline.
- Flowmeter grounding requirements: the flowmeter should be reliably grounded and cannot be shared with the ground wire of the strong current system.
Model Selection
Certifications
Q: How long is your delivery time?
A: it depends on the quantity. Normally it's about a week to two weeks.
Q: How to get quotation?
A: Please tell us the pipe diameter, measuring medium, flow rate, temperature, pressure, connection type and accuracy of the product you need, we will choose the most suitable product for you.
Q:can i design our own logo or color ?
A:sure ! we are glad to help you.
Q:Can I place a small order for the first time?
A:YES. This shows your recognition of us, I believe we will have longer-term cooperation.
){kind=link}