Small Flow CO2 Argon Gas Flowmeter Micro Thermal Gas Mass Flow Meter

• Customization: Available
• After-sales Service: Technical Support
• Warranty: 1
• Model NO.: ATMF
• Main Application: Nature Gas, Corrosive Liquid/Gas
• Size: DN10-50
• Sensor: Plug-in
• Application: Industrial Production
• Type: Volume Type Flow Meter
• Measuring Media: Gas
• Measuring Principle: Thermodynamic
• Measurement Object: Closed Pipeline
• Certification: CE, ISO
• Power Supply: DC24V or AC220V
• Working Pressure: Medium Pressure Less Than 4.0MPa
• Response Speed: 1s
• Pipe Material: Carbon Steel, Stainless Steel, Plastic, etc
• Output Signal: 4-20mA, Pulse, RS-485, Hart
• Ingress Protection: IP65
• Transport Package: Carton Box with PP Film Wooden Box
• Origin: China
• HS Code: 9026801000
• Production Capacity: 500 Piece/ Week
• Package Size: 20.00cm * 20.00cm * 10.00cm
• Package Gross Weight: 1.000kg
• Lead Time: 15 days (1 - 1 Pieces) ; To be negotiated ( > 1 Pieces)

Product Description

Product Description

Product Parameters

Performance	Technical parameter
Structural form	plug-in	pipe
Measuring medium	All gases (except acetylene)
Diameter range	Caliber DN32 or higher	DN10~DN200mm
Velocity range	0.1~120Nm/s
Precision	±1~2.5%
Operating temperature	Sensor:-40ºC~+120ºC        convertor:-20ºC~+45ºC
Working pressure	Medium pressure≤2.5Mpa	Medium pressure:4.0Mpa
Power supply	DC24V or AC220V≤18W
Response speed	1s
Output signal	4-20mA (Photoelectric isolation, large load 500Ω),pulse,RS-485 (photoelectric isolation),HART agreement
Alarm	1-2 relay normally open contact,10A/220V/AC,*/30V/DC
Type of supply	Separate structure, integrated structure
Pipe material	Carbon steel, stainless steel
Local display	Four lines of Chinese liquid crystal display
Display content	Mass flow, standard volume flow, cumulative flow, standard time, cumulative running time, standard flow rate, etc
Protection degree	IP65
Sensor material	Stainless steel	Stainless steel, carbon steel

Products Size

Why Choose Us

Installation Instructions

Installation Tips

1. Verify the actual internal diameters and wall thickness of the pipe before installing the Insertion thermal mass flowmeter.
2. First of all, 25 holes are opened in the pipeline, and the base is welded at the opening hole, and then the rest of the thermal mass flowmeter is loaded into the special ball valve together, and the depth to be inserted is calculated according to the actual pipe diameter and wall thickness. This step can be inserted to approximate size and hand tighten the nut.
3. Turn the sensor connecting rod so that the marked arrow is in the same direction as the medium flow.
4. According to the data measured in the field, convert the corresponding scale on the sensor connection rod, and lock the nut.
5. If you are horizontally installed, the display of this instrument can be flexibly installed at 90°, 180°, 270° to meet your actual needs.
6. 
   Mounting base
   
   Do not weld in an explosive environment.
   The environment with special requirements for welding should be operated in accordance with the relevant requirements.
   The base is divided into two types according to the different installation methods: welding and clamping. When installing, the base should be located at the apex of the section direction of the pipeline, and the axis of the base through the hole is perpendicular to the axis of the pipeline. The effect diagram of the welded base has been installed (the welding position has been treated with rust prevention).
   
   Installing ball valves
   
   Secure the stainless steel valve to the base. Use a gasket on the crimped contact surface (nylon material is used when the medium temperature is below 100 ° C, copper material is used when the medium temperature is above 100 ° C).
   
   punching
   
   Before drilling holes, check the site environment carefully to ensure the safety of operations.
   Close the valve in time after drilling to avoid air leakage.
   In the case that online drilling is allowed, the opening tool of Sen Ling Instrument Co.Ltd. can be used to realize online installation without stopping production. See related instructions for the use of the tool. When stopping drilling, a variety of methods can be used to punch holes, to ensure that the axis of the hole and the base of the hole axis concentric. If the hole is opened by gas cutting, the drilling operation should be arranged before the base welding

Model Selection

Certifications

        Q: How long is your delivery time?
        A: it depends on the quantity. Normally it's about a week to two weeks.

        Q: How to get quotation?
        A: Please tell us the pipe diameter, measuring medium, flow rate, temperature, pressure, connection type and accuracy of the product you need, we will choose the most suitable product for you.

        Q:can i design our own logo or color ?
        A:sure ! we are glad to help you.

        Q:Can I place a small order for the first time?
        A:YES. This shows your recognition of us, I believe we will have longer-term cooperation.